BQTHH - LATEX EGGSHELL STIPPLE ALL COLORS, 1615-SER

  • MSDS: BQTHH
  • Manufacturer: KELLY MOORE PAINT CO INC
  • Product Name: LATEX EGGSHELL STIPPLE ALL COLORS, 1615-SER
  • National Stock Number: 8010-00N036375
Product Identification

Product ID:LATEX EGGSHELL STIPPLE ALL COLORS, 1615-SER
MSDS Date:01/07/1987
FSC:8010
NIIN:00N036375
MSDS Number: BQTHH

Responsible Party
KELLY-MOORE PAINT CO INC
1015 COMMERCIAL ST
SAN CARLOS, CA 94070
US

Emergency Phone: 800-424-9300(CHEMTREC)

Info Phone: 415-592-8337

Preparer: JOE SCARRY

Cage: KELLY

Contractor
KELLY-MOORE PAINT CO INC
SAN CARLOS, CA 94070 US

Telephone: 415-592-8337

Cage: KELLY

Ingredients

PROPIONIC ACID, 2-METHYL-, MONOESTER

CAS: 25265-77-4

RTECS: UF6000000

Fraction By Weight: <2%


TITANIUM OXIDE; (TITANIUM DIOXIDE)

CAS: 13463-67-7

RTECS: XR2275000

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9293


SILICATES


CALCIUM CARBONATE

CAS: 1317-65-3

RTECS: EV9580000

OSHA PEL 15MG/M3 TDUST;5 RESP

ACGIH TLV: 10 MG/M3 TDUST


SILICA, CRYSTALLINE-FUSED; (SILICON DIOXIDE)

CAS: 60676-86-0

RTECS: VV7328000

OSHA PEL SEE TABLE Z3

ACGIH TLV: 0.1 MG/M3 RDUST;9293


BARIUM METABORATE

CAS: 13701-59-2

RTECS: CQ9570000


0.1

CAS: 62-38-4

RTECS: OV6475000

OSHA PEL SEE INGREDIENT NAME

ACGIH TLV: SEE INGREDIENT NAME

EPA Report Quantity: 100 LBS

DOT Report Quantity: 100 LBS


3,5,7-TRIAZA-1-AZONIAADAMANTANE, 1-(3-CHLOROALLYL)-,

CAS: 4080-31-3

RTECS: XX8450000

Hazards

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: DIZZINESS, HEADACHE, NAUSEA,
CONFUSION, IRRITATION TO UPPER RESPIRATORY TRACT, UNCONSCIOUSNESS,
SKIN/EYE IRRITATION. CHRONIC: NONE KNOWN.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:SEE YOUR PHYSICIAN FOR SPECIFIC
MEDICAL OPINION REGARDING YOUR CONDITION.

First Aid

First Aid:INHAL: REMOVE TO FRESH AIR. RESTORE BREATHING. CONSULT
PHYSICIAN. EYE: FLUSH WITH LARGE VOLUMES OF WATER FOR AT LEAST 15
MINUTES. GET MEDICAL ATTENTION. SKIN: WIPE OFF WITH A RAG. WASH
THORO WITH SOAP AND WATER. INGEST: CONSULT HOSPITAL EMERGENCY ROOM
OR POISON CONTROL CENTER IMMEDIATELY.

Fire Fighting

Flash Point:>200F,>93C
Extinguishing Media:MEDIA SUITABLE FOR SURROUNDING FIRE .
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE (DUE TO
BUILD-UP OF STEAM PRESSURE) WHEN EXPOSED TO EXTREME HEAT.

Accidental Release

Spill Release Procedures:VENTILATE AREA TO PREVENT BUILD-UP OR VAPORS.
FOR SMALL SPILLS, SOAK UP W/ABSORBANT. FOR LARGER SPILLS, DIKE AREA
WITH ABSORBENT MATERIAL AND SCOOP UP LIQUIDS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:STORE UPRIGHT IN SEALED CONTAINERS
AWAY FROM HEAT & FLAME.
Other Precautions:REMOVE AND WASH CONTAMINATED CLOTHING BEFORE REUSE.

Exposure Controls

Respiratory Protection:USE NIOSH/MSHA APPRVD PARTICLE MASK TO AVOID
BRTHG SPRAY MIST/SANDING DUST IF LOC VENT IS ADEQ TO KEEP TLV W/IN
ACCEPTABLE LIM. IF LOC VENT IS NOT ADEQ, THE USE OF AN NIOSH/MSHA
APPRVD RESP FOR ORG VA P, SUPPLIED AIR/SELF-CNTND (SUPP DATA)
Ventilation:LOCAL EXHAUT SUFFICIENT TO KEEP TLV BELOW PRESCRIBED
LIMITS.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
RESP PROT: BREATHING EQUIPMENT IS RECOMMENDED.

Chemical Properties

HCC:N1
Boiling Pt:B.P. Text:212F,100C
Vapor Pres:SEE INGRED
Vapor Density:LTR/AIR
Spec Gravity:1.2-1.4
Evaporation Rate & Reference:SLOWER THAN ETHER
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.
Percent Volatiles by Volume:55-65

Stability

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES WHEN
HEATED TO DECOMPOSITION AS IN WELDING.

Disposal

Waste Disposal Methods:DISCARD IN LANDFILL IN SEALED METAL CONTAINERS
AWAY FROM HEAT & FLAME & I/A/W LOCAL, FEDERAL & STATE REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.